Flooring & Tile

The specialty profiles that solve the tricky edges — where tile meets a lower floor, runs into carpet, turns an outside corner, or just needs a budget-friendly finish. Pair these with the aluminum edge trim to cover every transition on the job.

Which profile do I need?

• Reducer. Ramps tile down to a thinner adjacent floor for a smooth, trip-free transition.
• Carpet Edge. Caps the tile edge and grips the carpet where the two floors meet.
• Quarter-Round Edge. A softly rounded outside edge for tile corners and steps.
• PVC Edge Protector. The economical white edge finish for walls and backsplashes.

Specifications

The consumables that finish a waterproof install. Waterproof sealant seals seams, corners, and penetrations; the sausage gun and tips lay it down clean; mesh tape reinforces board seams; and screws, washers, and putty knives fasten and smooth. Stock the small stuff so the job doesn't stall.

What's here

• Waterproof sealant in 10 oz cartridge or 20 oz sausage.
• Sausage gun (with three tips) and replacement tips.
• Mesh tape for board seams.
• Screws & washers for fastening foam board — box or bucket.
• Putty knives, corner and flat, for smoothing sealant.

Specifications

The pre-built pieces that make a custom shower go up fast. Waterproof foam niches, bench kits, and curbs drop in ready to tile — no framing, no floating, no separate waterproofing. Set them, seal the seams, and finish in your tile.

What's here

• Recessed niches. Solid-foam shampoo niches with a finished opening — two sizes.
• Bench kits. Ready-to-tile corner bench forms in two footprints.
• Foam curbs. Pre-formed shower curbs in 60" and 96" lengths — cut to fit.

Specifications

The lightweight, waterproof substrate that replaces cement board. A rigid foam core between waterproof facing layers — it cuts with a utility knife, weighs a fraction of cement board, and needs no separate waterproofing on shower walls. Set it, tape and seal the seams, and tile.

Thinner boards make dead-flat walls and floor leveling; thicker boards build benches, curbs, and shims. Pick the size and thickness for the job.

Features

• Waterproof. Foam core with sealed facers — no additional membrane needed on walls.
• Lightweight & fast. Score-and-snap with a knife; a fraction of cement board's weight.
• Full thickness range. 1/8" leveling sheets up to 2" structural board for benches and curbs.
• Ready to tile. Bond directly with thin-set once seams are taped and sealed.

Specifications

Waterproof the assembly before the tile goes on. This peel-and-stick membrane bonds to shower walls, floors, benches, and curbs to create a continuous waterproof layer — then you tile directly over it. For floors over concrete or wood, the poly moisture barrier and vinyl adhesive keep dampness from ever reaching the finish.

Get the coverage you need: the 225 sf roll for full showers and wet rooms, or the 25 sf kit (primer & razor included) for small jobs and repairs.

Features

• Peel & stick. No hot mopping, no liquid cure time — roll it on and tile.
• Continuous waterproofing. Seals walls, floors, seams, and transitions in showers and wet areas.
• Primer & adhesive. Water-based primer for the membrane; vinyl PSA and 6-mil poly barrier for floor moisture control.
• Two sizes. Full 225 sf roll or a 25 sf starter kit.

Specifications

The visible finishing touch on a tiled shower floor. This 4″ grate and frame sit in the drain of a pre-sloped pan and set the tone at your feet — pick the finish to match your faucet, valve trim, and fixtures. Swap the standard strainer for one of these and the whole floor looks intentional.

Building from scratch? Grab the brass drain kit — the drain body, flange, and hardware that ties the grate to your waste line beneath a pre-sloped pan.

Features

• Four grate finishes. Matte black, oil-rubbed bronze, polished chrome, and brushed stainless.
• Linear-slot grate. Clean, modern lines with full drainage.
• 4″ standard. Fits Emser universal shower pans and standard 2″ waste outlets.
• Complete drain kit available. Brass body, flange, and hardware for a new build.

Specifications

The fast, foolproof base for a tiled shower. This pre-sloped, waterproof pan drops in over your subfloor, drains built to the correct pitch so water always finds the outlet — no mud-bed float, no guesswork. Tile directly over it once it's set and bonded.

Works for both curbed and curbless showers, and the offset-drain sizes let you place the drain off-center for longer, linear layouts. Every pan includes a brass drain, strainer/frame, and putty knives.

Features

• Pre-sloped & waterproof. Correct pitch molded in — ready to tile.
• Curb or curbless. Sized for standard and barrier-free showers.
• Center or offset drain. Offset sizes suit linear and walk-in layouts.
• Drain included. Brass drain, strainer/frame, and putty knives in the box.
• Extend it. Pre-sloped extensions and a low-profile ramp adapt the pan to larger footprints and curbless entries.

Sizing

Measure your shower's finished interior dimensions and pick the matching pan. For walk-ins and long runs, add a pre-sloped extension or ramp. Not sure which pan or drain position fits your layout? Ask MJ below — send a quick sketch.

Specifications

Flat floors start here. A tile leveling system pulls neighboring tiles to the same plane as the thinset cures, eliminating lippage — those slightly raised edges you catch with a bare foot or a mop. The clip sits under the joint, the reusable wedge presses down across both tiles, and once the mortar sets you snap the clips off at the floor line.

Essential for large-format tile, rectified edges, and anywhere a dead-flat finish matters. Build your kit below: pick your clip size to match your grout-joint spacing, add wedges, and grab the pliers for fast, consistent tension.

How it works

• Clips set into the thinset under the tile joint — one every few inches along the edge.
• Wedges push through the clip and press the tile faces flush; reuse them job after job.
• Pliers drive the wedge to firm, even pressure without over-tightening.
• Snap & go. After cure, break the clips off at the base — the wedges pop out to reuse.

Choosing your clip size

Clip size matches your grout-joint width: 1/32" and 1/16" for tight, rectified joints; 1/8" and 3/16" for standard joints. Wedges and pliers work across all sizes.

Specifications